Search results

Create the page "Intake/" on this wiki! See also the search results found.

Page title matches

• Intake/Exhaust Tightening Sequence
  57 B (7 words) - 13:52, 12 March 2006

Page text matches

• 1981
  ...x cylinder head and engine block redesigned for weight reduction. aluminum intake manifold, plastic valve cover and better casting techniques; idle speed con
  4 KB (598 words) - 15:08, 22 January 2006
• Diagram Section
  *[[Intake/Exhaust Tightening Sequence]]
  5 KB (552 words) - 01:42, 26 June 2010
• Header Pipe Back Renewal
  ...and are working on a small Eagle you may have to cut a few inches off the intake end of the intermediate pipe -- make sure you trial fit to determine how mu ...lier you may have to cut a very short length off of the intermediate pipe (intake end) to get it to work on a converter equipped small Eagle.
  4 KB (715 words) - 01:35, 7 February 2006
• Can I swap in a Chrysler 4.0?
  ...p may not be crucial for all assemblies. In addition the space between the intake and exhaust manifold mounting tabs may be too large for the factory washers ...mulitport injection set up. If you choose to inject and you use the stock intake weather it be Renix or HO (both use different harnesses and computers) you
  11 KB (1,967 words) - 16:00, 23 January 2010
• Joshpit's 4.0 Swap Article
  • The intake and exhaust header • And all other sensors on the intake and also the O2 Sensor on the header
  15 KB (2,754 words) - 16:41, 15 November 2009
• Comprehensive Index
  Engine, 258, Intake/Exhaust Manifold Tightening [[Intake/Exhaust Tightening Sequence]] Exhaust Manifold, 258, Tightening Sequende [[Intake/Exhaust Tightening Sequence]]
  14 KB (1,643 words) - 22:40, 29 April 2013
• Great Tips from tougeagle
  8. You can use your 4.2L intake manifold, though the dowels will not go through the holes, but under them.
  4 KB (758 words) - 00:13, 21 March 2011
• Converting to 4.0L cylinder head, EFI and cam - manual transmission
  91-2005 intake manifold (I used a 92, however the 98 and up equal length manifold will net Autozone 3" intake tubing and cone filter: 75$
  37 KB (6,837 words) - 00:40, 2 May 2011
• Overheating? Includes thermostat replacement
  ...mp gasket and weephole, thermostat housing, intake manifold (if stock, 4.0 intake is not water cooled), heater hoses, coolant temp sensors and heater core. I
  6 KB (1,168 words) - 04:47, 10 May 2011
• Other Carter carb tips
  ...having problems with your car idling poorly, check the bolts that hold the intake and exhaust manifold to the head and make sure they are tight. Next check a
  1 KB (250 words) - 22:29, 29 April 2013
• Building A Stroker Info
  ...below except for 0.030" overbore, Ford Motorsport 24lb/hr injectors, stock intake, and 62mm TB. ...evels. To get maximum benefit from the stroker engine you need a free-flow intake with Powerstack or K&N cone filter, 62mm bored HO throttle body, header, hi
  12 KB (1,805 words) - 18:51, 26 June 2011
• Vacuum Lines Made simple
  ...ires a direct connection to manifold vacuum.  I recommend the port on the intake just below the carb that is shared w/ the brake booster.
  646 B (123 words) - 15:01, 1 August 2011
• Junkyard Hydroboost in an Eagle
  BTW, the booster can be mounted upside down for more clearance on the intake manifold side. I have not tried this, so it may present other challenges su
  6 KB (1,144 words) - 20:28, 30 September 2014