Automatic to Manual Transmission Swap

From Eaglepedia
Revision as of 16:06, 20 January 2007 by IowaEagle (Talk | contribs)

Jump to: navigation, search

Contributed by AMC Eaglen Nest member "monsterbronc"

OK, I did it, the eagle is now a stickshift, and all I can wonder. is why would anybody want an auto? this thing drives sooo much better with a stick, before at 70 mph my foot was on the floor, now its on the floor to get there, but holds speed well at part throttle, ive even broke 85mph. I bet my fuel mileage just went wayyyy up.


1981 AMC Eagle auto to T-4/5 swap

ok, here it is, the complete tranny swap guide thingy.

Disclamer: I am not responsible for anything, got that? If you mess something up or hurt yourself or someone else, its your own fault, not mine.

I also give permission for this to be copied, exchanged, given, moved, reposted, pretty mutch feel free to use this however you want, but under no circumstances is it to be sold. This is free for everyone.

Please bear in mind, I did this in a hurry, and in lower 20’s F weather, outside on my lawn. so if something I did seems unsafe, it probably was unsafe, and you should think of a safer way to do it. For instance I did all the lifting of transmissions and stuff, when Had I been in a shop on a concrete floor, I would have used a jack.

You will need

A t-4 or 5 transmission with GM 10 spline input (you can swap inputs, I did)

A 258 to t-4 or 5 bell housing (try to find one with fork)

A 258 flywheel for 10.4 inch clutch

6 flywheel bolts

6 pressure plate bolts

4 transmission bolts

Clutch kit, includes: Disc; Pressure plate; Pilot bearing; Throwout bearing; and a Disc centering tool

Throwout fork

Eagle clutch and brake pedals

Eagle slave and master cylinder for the clutch, with resivoir and hose

Shifter and shifter boot


Basic sockets and wrenches did the trick, I never needed my ½” drive.

And most importantly GOOD MECHANICAL SKILLS, if changing your oil is complicated, than DO NOT ATTEMPT.

If you don’t have a tourque wrench, I suggest getting one, they come in handy when dealing with drivetrain stuff, Home Depot has a Husky, ½” drive for like $60 or so, and as a mechanic, that’s a DEAL. And its lifetime warrentied, my Matco ones aren’t, and cost over $200 next one I buys gonna be that Husky.

part #s slave rebuild kit brake best- chk351835 lifetime warrenty

clutch kit 10.4 inch disc dynapack- nu1916-2 lifetime warranty

T-4 transmission, out of 81 jeep scrambler, PN unknown

258 bell housing off 83 cj PN unknown (wrong one, had low mount for fork)

pilot bushing federal mogul pb-79

10 spline input shaft 1351085008r, brand unknown

all other parts are off of other eagles, so I do not know specifics


Step one remove the auto, pretty simple

Lift up front of vehicle and set tires on blocks, or pull onto ramps, chock back wheels and apply park brake.

Unbolt any skid plates you might have under the t-case, mine had 5 bolts holding it on. Now disconnect the driveshafts fron the t-case, and just push them out of you way, you don’t need to completely remove them, I didn’t.

Next, unhook the linkages and cut the 3 prong plug off for the reverse lights and the neutral safety, it wont fit the new tranny.

Mine had the shifter on the floor, so go ahead and pull the carpet back a little and remove the shifter plate to expose the hole in the floor.

Place a jack under the tranny to support it, and remove the crossmember, then slowly let the jack down. Now you have acess to the top bolts on the bell housing.

Then I unbolted the studs holding the t-case to the tranny, it dosent matter if the nuts come off or if the studs pull out, you can put the studs back in before you put it back together.

Now place a pan underneath the rear of the tranny, and pull the t-case off. Any oil should be caught by the pan. Slide the t-case out of you way, careful not to damage the speedo cable. And to keep from making too much of a mess, stuff a plastic grocery bag in the end to slow the drip.

Remove the starter and just let it hang, it wont hurt it, I do it all the time.

Pull off the flywheel cover plate, and remove the four bolts holding the tourque converter to the flex plate, you will need to pry the engine over a couple times for this.

Now remove the two side bolts on the tranny, they take a 5/8, then the two above them, 9/16, but remember they have a nut on the other side,(don’t ask me why).

Now remove the dipstick tube(use the pan again, and another grocery bag to fill the hole) Then with the tranny supported undo the three top bolts9/16, and the tranny is free.

Now unbolt the 6 flywheel bolts, and we are ready to start the swap.

First thing to note is the T-4 is about 1 ½” shorter than the tourquflight, but its not enough to bother the driveshafts…..


Automanualtrans.jpg


Step two clutch install, still pretty simple

With new bolts,(the flexplate bolts are too short, so buy new flywheel bolts for a jeep with a 258) attach the flywheel, if its grooved get it resurfaced, mine was ok, so I just bolted it on as is.

Torque the bolts to 105 ftlbs, per amc tsm.

Now use a brass rod, or a socket and extetion to hammer a well oiled pilot bering into the hole in the crankshaft.

Then use the centering tool to hold the disc in place while you start the bolts for the pressure plate, making sure the disc is centered be feeling around the edges.

Torque the pressure plate bolts to 28 ftlbs per amc tsm.

Now it should look like this….

Pressureplatedisc.jpg


Now its time to bolt on the bell housing, but you need the right one, its best to find out if you have the right one before you get the tranny bolted on, I didn’t. I had the wrong one, and had to pull it all apart again, I actually got the T case bolted on before I figured it out. So I pulled it back apart and modified it, the problem is, that there are two throwout fork configurations, a high and low, an eagle needs a high, or you end up with a problem like this…..

Problem01.jpg
Problem02.jpg


As you can see, the slave will bolt into both positions, but on the eagle the front axle and driveshaft are in the way, so the upper position is mandatory.

So to fix it, I broke off the post for the pivot ball, and built my own by welding a bolt to a plate and pressing the old pivot onto the bolt. Then I used self tapping screws through predrilled holes to mount the new pivot in the right position for the upper mount configuration. I would give measurements, but I didn’t measure, I just eyeballed it, I tend to get better results that way.(space and time alter when Im around a welder) when done it looked like this…..

Slavecylinderinstall01.jpg
Slavecylinderinstall02.jpg
Slavecylinderinstall03.jpg
Slavecylinderinstall04.jpg